Wall Supply Fans – Canada Fans Industrial Blowers & Fans

Industrial Fans & Noise

The important factor to consider is the fan’s blade pass frequency, which is a pure tone produced when the blades of the fan wheel (impeller) rotate past the housing cut-off sheet in centrifugal fans, or the turning vanes, in axial fans. The blade pass frequency is calculated by multiplying the number of blades times the rotating speed in revolutions per minute. If this frequency matches the natural frequency of the ductwork, it can excite the ductwork, which can cause it to resonate, thereby increasing the noise level. Because of this possible increase in sound, and because certain pure tones are irritating to people, the sound output of the blade pass frequency should be investigated when sound reduction is desired. The next factor to consider is the fan design. Generally a fan operating at peak mechanical efficiency will produce less noise, because high efficiencies result from minimal air turbulence within the fan.

The sound generated by some fans can be a potential hazard to personnel in close proximity to the fan, and the sound can be transmitted, via the ductwork connected to the fan, to all areas serviced by the fan. Because of these concerns, fan manufacturers publish sound ratings for their products to serve as a guide for selecting fans to meet sound specifications, and to assist acoustical consultants in predicting the total noise levels in specific environments. This article provides basic information to help understand fan sound ratings and how to apply them. Like any mechanical device, fans generate sound, which emanates naturally from the turbulence of moving air, the mechanics of moving parts of the fan, and from vibration.

Air turbulence within the fan increases the sound coming from the air movement. The noise resulting from air turbulence is a major factor in the sound levels of a fan in a specific application. Further, duct work can transmit this turbulent noise to all areas serviced by the fan. Factors contributing to air turbulence include the resistance to flow, flow separation along fan surfaces, and shock related to abrupt changes in the direction of airflow, pressure, or velocity. A lower noise level can be achieved by reducing air turbulence. This can be done by considering several factors related to air movement when selecting fans.

Industrial Centrifugal Fans Design

There are four basic centrifugal fan wheel designs – forward curved, backwardly inclined, radial, and radial tip – and a variety of axial flow wheel designs. Each wheel design has unique sound characteristics due to the way they handle air, and the efficiencies they can achieve. Fan speed does not always determine which fan will be quieter. For example, centrifugal fans have higher amplitudes at lower frequencies, while axial fans exhibit higher amplitudes at the higher frequencies. The amplitude of the blade pass frequency on an axial fan is higher and more pronounced than on backwardly-inclined fans, and commonly will have amplitude peaks at multiples of this frequency.

Backward Inclined Fans

Of the four centrifugal designs, the backwardly inclined fans are the most efficient, and therefore, the quietest. Those with airfoil-shaped blades offer the highest efficiencies, for clean air environments, while those with single-thickness blades can be used in applications where light dust or moisture is present, although the efficiencies are somewhat lower.

Axial & Vaneaxial Industrial Fans

Certain types of axial fans offer the next highest efficiencies. An excellent example is the Vaneaxial fan that uses airfoil shaped blades in an in-line flow design. This fan is used to handle high volumes of clean air at low pressures, which is a typical ventilation application.

Radial Blade Fans

Radial fans are typically low efficiency, open designs for special purpose applications, such as bulk material handling, or exhausting / supplying lower volumes of air at higher pressures. A radial fan will be much louder than a backwardly-inclined fan operating under the same volume and pressure conditions.

Radial Tip Fans

Radial Tip fans, commonly used to handle larger volumes of air that contains particles or material, exhibit sound characteristics similar to the radial fans. The sound spectra of radial and radial tip fans contain amplitude spikes at various frequencies, and a noticeable spike at the blade pass frequency.

Forward Curve Fans

The forward-curved fan design operates at speeds that are much slower than the other fan types, which results in lower noise levels from mechanical operation and vibration. However, because of its modest efficiencies, a forward curved fan may be noisier than a backwardly-inclined fan when operating at comparable volume and pressure. The sound spectrum of the forward-curved fan shows a slower rate of reduction in amplitudes than the other centrifugal types, and because of the large number of blades, the blade pass frequency occurs much later in the spectrum and is not predominant.

Industrial Fan Components

The moving components of the fan – the motor, bearings, and drive – produce sound. This too can be transmitted through the system via the fan structure or shaft, or when these components are in the airstream. Motor sound will vary with speed, enclosure, electrical characteristics, and even the manufacturer. Antifriction bearings can be used to reduce bearing noise, and proper drive selection will reduce the likelihood of belt hop, or slap. Of course, proper maintenance must be employed to keep the moving parts running smoothly, and quietly.

Excessive vibration can significantly add to the overall noise level of an installation. This will occur if the fan or any of its components are not adequately balanced, if the fan is installed on an insufficient foundation, or if the fan is not properly isolated from other system components. For example, it is not uncommon for the fan’s support structure or ductwork to have a natural frequency at the fan’s operating speed or blade pass frequency, either of which can cause the system to resonate at that frequency, increasing the sound levels, and the possibility of damaging the installation. These risks can be eliminated by changing the speed of the fan, installing appropriate isolation, and / or detuning of the fan or affected system components.

dBA is a useful measurement for evaluating the overall noise level at a particular location, but this measurement takes into account all of the sound sources affecting that particular location, which include the sounds from all equipment in the area, natural sounds of the environment, and from other environmental factors. Some of these factors are the current physical properties of the air such as temperature, humidity, and pressure, whether the location is outside or inside, the size and material of the room. All of these affect the sound pressure experienced by the listener, and recorded by the sound level meter.

Published fan sound power ratings and corrections only reflect noise created by air turbulence within the fan. Because of the infinite variables, mechanical noise and vibration noise are impossible to accurately predict, and are not included in the rating.

Additional information can be found at the Northern Fan web site http://northernindustrialsupplycompany.com/products/ventilators.html

Oleg Cthetchel
Air Process Systems Engineer
nis@primus.ca
Northern Fan Co.
http://northernindustrialsupplycompany.com
http://northernindustrialsupplycompany.com/burlington/request6.html

Fans and Blowers Noise Levels

nis@primus.ca

fan,ventilator,blower,industrial,commercial,ventilation,ventilating,roof ventilator,wall ventilator,roof fan,wall fan

olegsystems

***

Tags:
Axial Roof Ventilators, Axial Ventilator, Blower, Blower Fan, Blower Fan Canada, Blower Fan Suppliers, Blower Industrial, Centrifugal Blower Fan, Centrifugal Blower Fan Suppliers, Industrial Centrifugal Blower, Industrial Centrifugal Fan, Industrial Fans, Industrial Fans and Blowers, Industrial Pressure Blower, Inline Belt Drive Fans, Inline Exhaust Fans, Material Handling Fans, Mixed Flow Inline Fan, Radial Blade Belt Centrifugal Fan, Radial Blade Centrifugal Fan, Radial Blade Fan, Radial Blade Pressure Blower, Roof Exhaust Fans, Vaneaxial Fans Aluminum Wheel, Vaneaxial Power Roof Ventilator, Wall Exhaust Fans, Wall Supply Fans

Industrial Fans Canada

People these days opt to use fans for their ventilation needs. A mechanical fan often has many uses around the house and inside buildings. This versatile appliance can serve as a cooling instrument especially during the summer and it can also be used during winter to push warm air down in order to heat a room.

Axial fans, centrifugal fans

In the industry, there are many types of fans such as axial fans, centrifugal fans, crossflow fans and bladeless fans. These types of fans have features, structures and benefits. Each one offers different processes and ways of balancing the temperature. Their usage also depends on the kind and size of the room that needs ventilation. This enables engineers to choose the right kind of ventilation that will coincide with the design they have in mind for their buildings.

Axial Fans

Axial fans are the typical household fans we see every day. This type of fan has three or more blades that rotate to allow air to pass through and circulate around a room. Axial fans are operated by electricity to balance the temperature and permit air to flow inside a room.

Damper Fan

A damper fan is a duct-like device used to neutralize temperature through ventilation ducts. There are many damper manufacturers who produce fire dampers that help prevent the spreading fires in buildings and houses. These fans are designed to close once subjected to heat and/or fire. Engineers and architects are incorporating fire dampers in their design to effectively reduce the damage that a fire can cause.

A dampers manufacturer makes sure that its products are safe for use by consumers. They make certain that their products materials are of the highest grade and quality so as not to risk the safety of the building where the fans will be used.

Centrifugal Fan

A centrifugal fan manufacturer sells fans that are quite different from the other types of fans. This type of fan is composed of different instruments which control the fans speed. It is a typically larger mechanism compared to other fans to accommodate bigger structures like office buildings and factories. All of these fans aim to maintain the convenience of the people regarding temperature balance.

Some Of The Industries That Heavily Require Ventilation Are:

•Pharmaceutical Industry
•Biological Industry
•Chemical Industry
•Mining Sector
•Physical Research Industry
•Processing units

For additional information please refer to http://www.industrialblowerfan.com

Susanna Terlitskaia
Industrial Ventilating Engineer
Industrial Blower Fans Company
nis@primus.ca
http://www.industrialblowerfan.com/axial-fans-man-coolers.html
http://www.industrialblowerfan.com/scrubbers-dust-collectors.html

Fans and Dampers

fan blower ventilator high temperature pressure gas-tight air-tight zero emission industrial sulfur recovery heavy duty capacity process chemical steam jacket jacketed double wall housing shaft seal mechanical

nis@primus.ca

industrialblowe

fan,blower,ventilator,high,temperature,pressure,gas-tight,air-tight,zero emission,industrial,sulfur recovery,heavy,duty,capacity,process,chemical,steam,jacket,jacketed,double wall,housing,shaft seal,mechanical

http://www.nisco.net/tchetchel.gif

***

Industrial Fans – Types

Different models of fans are available in the market in various unique designs, integrated with the latest technologies and low power consumption facilities. The variety of elegant fans includes integrated gear box and push button switch to suit any decor.Many stylish fans with double ball bearing are available in lots of colors which are integrated with dynamically balanced blade for maximum air delivery.The use of radial blower in the fans helps in moving air perpendicular to the blower axis and provides relatively low flow rates and high pressures.

Types of Blowers & Fans

The wide range of blowers and fans includes non-decorative Ceiling fans, wall mount fans, decorative ceiling fans, single centrifugal blowers, dual centrifugal blowers, radial wheel blowers, cast aluminum blowers, high pressure blowers, belt driven blowers, explosion proof and food safe blowers, high temperature oven circulating fans, industrial fans and also stainless steel and other alloy fans are available in the market. Finest quality, durability and enduring performances of these fans are catching more attention of the market these days. A wide range of axial flow fans is designed to provide efficient trouble free service & reduce the initial and operating cost to minimum. Apart from the fans there are various other products like air blowers, air scrubbers, axial fans, axial flow fans, centrifugal blowers, cyclone seperators, dust collecting equipment, dust collector, exhaust blowers, fan blowers, industrial blowers and many more.

Non-Decorative Ceiling Fans are integrated with the low power consumption facility with double ball bearing for maximum air delivery and available at very reasonable price. Non-Decorative Ceiling Fans are high speed fans, which are available with four blades to provide maximum air delivery and best for all small rooms. Non-Decorative Ceiling Fans has variety of designs and colors available at the best competitive prices. Non-Decorative Ceiling Fans consists of power saving technologies which make it more unique and high monopoly holder in the competitive market.

Wall Mount Fans are available in sleek and stylish look with less noise and delivers maximum air pressure. Wall Mount Fans are integrated with aluminium blade coated which increases its life and also gives an elegant look to your room. Wall Mount Fans are available in many colors like Blue, Red, Brown, Cherry and lots more.

Decorative Ceiling Fans are one of the most demanding ranges of fans in the market. The aluminium body with golden touch offers a unique look and suits any decor. These days, the latest technology of power saving in fans attracts the market and consumers as well.

For additional information please refer to http://www.industrialblowerfan.com/products.html

Susanna Terlitskaia
Industrial Ventilating Engineer
Industrial Blower Fans Company
nis@primus.ca
http://www.industrialblowerfan.com/feedback.html
http://www.industrialblowerfan.com/contact.html

Fan Types

nis@primus.ca

industrialblowe

fan,blower,ventilator,high,temperature,pressure,industrial,super,transfer,air,gas,positive,negative,heavy,duty,capacity,process

http://www.nisco.net/tchetchel.gif

***

Industrial Exhaust Fans

Exhaust fans can be grouped into two general categories: emergency smoke evacuation and process ventilation. Generally speaking, emergency smoke evacuation fans may never be used, but they must be installed and be capable of exhausting high temperature air and smoke in the event of a fire. In contrast, high temperature process ventilation requires continuous duty exhaust of high temperature air, fumes or particulate. Both application types are uniquely different requiring special construction and system design considerations. In this article, we will examine both types of exhaust applications, looking first at the emergency smoke exhaust category. Since emergency smoke exhaust deals with lifesafety issues, there are governing bodies in place that identify and regulate specific design and performance standards. The administration and organization of the various governing bodies is subject to modification based on the needs of the industry. Currently, four such agencies are Industrial Risk Insurers (IRI), Southern Building Code Congress International, Inc (SBCCI), the National Fire Protection Association (NFPA), and Underwriters Laboratories, Inc. (UL). IRI insures properties all over the world based on an informational manual, which details the construction requirements that belt drive emergency heat and smoke exhausters must meet in order to be covered by IRI.

SBCCI is a not-for-profit organization of government officials from the United States and several foreign governments, which serves a strong leadership role in the delivery of model building codes. The purpose of the NFPA can be summarized into three main categories. First, NFPA promotes the science and improves the methods of fire protection and prevention, electrical safety, and other related safety goals. Secondly, it obtains and circulates information on these subjects. And thirdly, it secures the cooperation of its members and the public in establishing proper safeguards against loss of life and property. The fourth organization is Underwriters Laboratories, Inc.. UL is a non-profit, independent organization that maintains and operates laboratories for examination and testing of devices, systems and materials to determine their relation to life, casualty hazards and crime prevention. UL has three safety standards that apply to emergency smoke exhaust products. UL705 is concerned with the mechanical and electrical construction to insure safe operation. All electrical components (motor, wiring, switches, enclosures, etc.) must be ULlisted. UL793 is concerned with the lifting mechanism for the butterfly dampers and the fusible link. In order for a product to be listed in the UL Directory under ÒPower Ventilators for Smoke Control Systems,Ó it must meet the requirements of both UL705 and UL793. Additionally, UL must witness a full-scale test of a fan operating for the required time at the specified elevated and temperature.

High Temperature Exhaust Fans

So what makes one fan more capable of sustaining higher temperatures than another fan? Each model has a recommended maximum operating temperature based on the construction materials, drive components, and airflow characteristics. The limiting temperature is determined to be the highest temperature that any component of the fan assembly will reach during any operating cycle. Similarly, the maximum operating temperature is typically determined to be the lowest temperature that begins to exceed the capacity of any one component. For example, in some cases the bearings may be the limiting component, while in other cases the fanÕs impeller construction material may be the limiting component. The construction material is perhaps the most obvious element of the fan to consider when dealing with a high-temperature application. In general, aluminum withstands maximum temperatures up to 250 F, standard carbon steel up to 750 F, and 316 stainless steel up to 1000 F. Critical components are many times constructed of ferrous materials to withstand the higher temperatures. If temperatures were to exceed 300 F, for example, aluminum would be eliminated as a construction material option. Other construction considerations include bearing type, drive component selections, means of ventilation and cooling of the drive components, and insulation options.

The most common way of simplifying construction and component specifications to accommodate high temperature applications is to maintain separate categories based on the specified temperature range and time requirements.

Canada Fans has four Heat Option Packages for high temperature operation. Heat Option I construction is designed for continuous operation between 200 F and 500 F. Heat Option II construction meets specifications requiring the fan to exhaust 500 F air for a minimum of four hours in an emergency smoke removal situation per IRI requirements. Heat Option III construction meets the specifications requiring the fan to exhaust 1000 F air for a minimum of 15 minutes in an emergency smoke removal situation per SBCCI. This construction also surpasses the IRI requirements for 500 F for a minimum of four hours. Heat Option IV construction meets specifications for UL Listed ÒPower Ventilators for Smoke Control Systems. This includes the IRI requirement of 500 F for a minimum of four hours, the SBCCI requirements of 1000 F for a minimum of 15 minutes, and the Snow Load Test for butterfly dampers in UL-793.

While it may be tempting to choose a higher heat option than necessary “just to be safe”, doing so can add considerable and unnecessary cost to the job. For example, selecting HT Option III when HT Option II is adequate adds insulation and high temperature bearings. These items would be considered “overkill” and add unnecessary extra costs.

For additional information please refer to http://www.northernindustrialsupplycompany.com/products/industrialfan_blowers.html

Oleg Cthetchel
Industrial Process Engineer
airknife@cogeco.ca
Northern Fan Co.
http://northernindustrialsupplycompany.com/products/index.html
http://northernindustrialsupplycompany.com/products/industrialfan_blowers.html

High Temperature Exhaust Fan

airknife@cogeco.ca

high temperature fan,high temperature blower,high temperature ventilator,oven exhaust fan,oven exhaust ventilator,oven circulation fan,oven circulating fan

buffalofancom

***

Industrial Ventilators for Ventilation

Industrial ventilation is of paramount importance to ensure the safety and well-being of employees. In industries where employees are subjected to dangerous chemicals, vapours and gasses on a daily basis, effective industrial ventilation can mean the difference between life and death. The basic concepts behind industrial ventilation are quite simple, but for it to be effective, the ventilation system needs to be installed by an experienced engineer.

Industrial Ventilation Methods

Industrial ventilation is a method of controlling employee exposure toxic chemicals, volatile airborne substances and flammable vapours by removing the contaminated air and replacing it with clean, fresh air. Used in a variety of different industries where poisonous vapours may be a problem, industrial ventilation is most often employed to remove welding and solvent vapours, oil mists and poisonous or volatile dust.

But, industrial ventilation may not always be necessary. True, it should be preferable for the continued health of your employees, but regulations suggest that industrial ventilation only becomes compulsory when:

•the levels of contaminants exceed regulated levels;
•the lower explosive limit of flammable vapours is exceeded; or
•when the oxygen concentration in an area drops below 19.5%.

Industrial ventilation should also be considered before respirators. Not only is the system easier to maintain, but, in the long run, is a much more cost effective method of air purity control.

Industrial Ventilator Options

There are a number of industrial ventilation options available depending on the circumstances of your industry’s circumstances. The most basic is indoor quality ventilation that aims to provide fresh air throughout a building as part of the existing ventilation system. This option is primarily used in offices but can be effective in small industries where the concentration of contaminants is low.

Easy to maintain and inexpensive to set up is dilution ventilation. This form of industrial ventilation uses large and powerful exhaust fans to extract contaminated air and to draw in clean air. It is very effective in clearing flammable vapours but is less effective for metal fumes or large concentrations of highly toxic materials. Depending on where the industry is located, the incoming air may require a lot of cooling or heating before it can be introduced into the industrial ventilation system, increasing the cost of using the system.

Dilution Ventilation Principles

Dilution ventilation uses the simple principles of displacement and dilution to function. Some of the contaminated air is removed and replaced with large amounts of fresh air. The concentration of the contamination is effectively lowered, making it safer for people to work in the area.

A more localised industrial ventilation system is local exhaust ventilation. This system captures the contaminations at the source and expels it before it has a chance to disperse into the air. For highly toxic contaminants or high concentrations, this industrial ventilation is probably one of the best. It does not require large amounts of fresh incoming air since the exhaust of contaminants is localised. This effective ventilation comes at a higher cost and more frequent maintenance, however.

Local Exhaust Ventilation

Local exhaust ventilation works like a vacuum cleaner forcing contaminated air to move from a high concentration to a low concentration. It is perhaps one of the most effective industrial ventilation systems because it removes the contaminants at the source before it has a chance to spread.

There are effective industrial ventilation systems available for any industry. Some are simple to use, like dilution ventilation, while others are specifically made for highly toxic environments, like local exhaust ventilation. Whatever the decision, as long as the industrial ventilation keeps your employees safe from the contaminations of the substances they work with, it is doing its job.

For additional information please refer to http://www.industrialblowerfan.com/projects.html

Susanna Terlitskaia
Industrial Ventilating Engineer
Industrial Blower Fans Company
nis@primus.ca
http://www.industrialblowerfan.com/air-cooling-unit.html
http://www.industrialblowerfan.com/roof-extractors.html

Industrial Air Ventilation

nis@primus.ca

industrialblowe

fan,blower,ventilator,high,pressure,industrial,stainless,alloy,fiberglass,FRP,PVC,Propylene,Polypropylene,PVDF,corrosion,resistant,corrosive,resistance,heavy,duty,capacity,process,exhaust

http://www.nisco.net/tchetchel.gif

***

Mixed Flow Inline Fans

Made by Canada Fans Co. high pressure MVA series mixed flow inline ventilators finally resolves the problem of pushing air through high resistance and long ventilation ducts.

Mixed Flow fans are an excellent choice for return air, supply, or general ventilation applications where low sound is critical. As compared to similarly sized tubular centrifugals and vane axials, a mixed flow fan will be 5-20 dB quieter! In addition, the mixed flow wheel is extremely efficient and will cut down on operating expenses.

Unique features of the MVA Mixed Flow Fans include:

– Universal Mounting System that allows the unit to be field rotated at the job site
– Compact design with standard slip-fit duct connections for ease of installation
– UL/CSA listing for electrical is available
– Continuously welded housing with a standard powder paint finish suitable for indoor or outdoor applications
– A complete three plane vibration test of all assembled fans prior to shipment

Mixed Flow Inline Fan: Model MVAB:

* Belt drive construction with motor out of the airstream
* Air Handling Quality bearings selected with a minimum life in excess of L(10) 50,000 hours at the maximum operating speed
* Performance capacities from 1,000 to 100,000 cfm (1,700 – 165,000 m3/hour) and pressures up to 8 in. wg. (2000 Pa)

Mixed Flow Inline Fan: Model MVAD:

* Direct drive construction eliminates belts, pulleys, and shaft bearing maintenance
* MVAD design is more compact for space critical application
* Partial wheel widths allow for wide performance capacities ranging from 500 to 105,000 cfm (900 – 170,000 m3/hour) and pressures up to 9 in. w.g. (2300PA)

Vaneaxial Fans

Another in-line fan for for air moving in round ducts by Canada Fans is a high pressure small vaneaxial fan finally resolves the problem of boosting air flow in long ventilation ducts of today’s large residential houses.

For a long time the efficient ventilation of remote rooms in the large houses could be done only with two independent air supply sources (like a furnace). Ventilating ductwork in contemporary large houses becomes so long and elaborated that even a high pressure furnace fan couldn’t generate enough static pressure to blow through the whole length of such a duct. The existing low pressure booster duct fans, even though compact enough to be installed in-line in the house ventilation ductwork, still do not provide enough booster pressure / airflow. The usual solution to this problem was installation of two independent furnaces with different air ducts, which is rather expensive option.

High Pressure Fans

A new high pressure (up to 1.5″ WG) small vaneaxial Series VA fan is an ideal booster fan for prolonged ducts. Unlike inline centrifugal ventilator, that also generates rather high pressure, the air comes out not from a peripheral outlet ring area, but distributes evenly across its outlet opening like in true axial blowers.

The other advantages of VA Series vaneaxial ventilators is their intrinsic spark-resistant construction because of all-aluminum construction; quiet operation of true vaneaxial design; lower energy consumption due to efficient wheel design.

Eight different sizes from 6″ DIA to 10″ DIA offer wide performance range for any ventilation duct design. Direct drive design ensures long live, maintenance-free operation. Explosion proof motors are available too, as well as sliding dampers, various mounting options, additional sound isolation.

For additional information please refer to Canada Fans Co. web site http://northernindustrialsupplycompany.com/index.html.

Oleg Cthetchel
Process Ventilation Engineer
Canada Fans Co.
http://northernindustrialsupplycompany.com/products/industrialfan_blowers.html
http://northernindustrialsupplycompany.com/products/ventilators.html

High Volume Inline Mixed Flow Fans

fan ventilator blower axial inline mixed flow tubeaxial duct vaneaxial centrifugal tubular ventilating ventilation

fan@cogeco.ca

fan,ventilator,blower,axial,inline,mixed,flow,tubeaxial,duct,vaneaxial,centrifugal,tubular,ventilating,ventilation

***

Selecting an Industrial Fan

The air delivering capacity of axial flow fans ranges from 100 to 500,000 cubic feet per minute (3,000 to 15,000 cubic meters per minute). Impellers usually have blades with airfoil cross-sections.

Axial Fans

In an axial fan, the effective progress of the air is straight through the impeller at a constant distance from the axis. The primary component of blade force on the air is directed axially from inlet to outlet and thus provides the pressure rise by a process that may be called direct blade action.

The blade force necessarily has an additional component in the tangential direction, providing the reaction to the driving torque : this sets the air spinning about the axis independently of its forward motion.

As compared to curved sheet blades, aerofoils can apply greater force to the air, thereby increasing maximum pressure and can maintain better efficiency over a wider range of volumetric flow. Also by increasing the thickness & curvature of the inner sections, the blades can be made stiffer, this limits flutter and allows the impellers to be run at higher speeds.

Selection of a a right fan one should consider such factors like cost optimization, power rating & noise levels govern the selection of a fan suitable for a given application. Various combinations are possible to meet any given duty or operating requirements for best performance, lesser noise, power and cost characteristics.

Once the volume of airflow and the static pressure of the system are known, it is possible to specify a fan. The governing principle in fan selection is that any given fan can only deliver one flow at one pressure in a given system. To select a fan one must consider the following parameters:

– total airflow required

– total operating pressure

– fan installation space

The fan efficiency is defined as the ratio of air power (output) to shaft power requirement (input). An optimally designed fan impeller with improved aerodynamics requires less shaft input power for desired delivery of air volume with total pressure rise as per the system requirement. With reduced shaft power requirement, there is a commensurate reduction in energy consumption.

Thus the fan efficiency is directly contingent upon selection of fan and the operating point relevant to the system resistance.

The way fan impellers (blades or rotors) are designed, the amount of air they can move decreases as the pressure they are working against increases.

The airflow vs. pressure information for a particular fan is called the fan performance data. The performance of a fan depends on the size, shape & speed of the impeller. The fan performance data is essential for selecting fans as per the desired airflow and system pressure.

Most fans are tested using procedures specified by Air Movement and Control Association International Inc. (AMCA), Illinois, USA. The fan under test is mounted near the outlet of the test rig and air in-flow through the rig is varied by the movable gate assembly situated at the other end of the test rig.

The airflow through the rig is determined by measurement of the pressure differential and simultaneous readings are taken of the static pressure developed by the fan, air velocity at the exit side, power consumed by the fan driving motor etc.

Fan performance curves and data show how much pressure and airflow a given fan can produce at a given speed. This data is based on the system resistance (pressure) occurring away from the fan. Fan performance curves are developed by fan manufacturers based on the testing of a prototype fan fabricated based on the theoretical design.

The axial flow fans are widely used for providing the required airflow for heat & mass transfer operations in various industrial equipment and processes. These include cooling towers for air-conditioning & ventilation, humidifiers in textile mills, air-heat exchangers for various chemical processes, ventilation & exhaust as in mining industry etc. All the major industries use large number of axial flow fans for operations, such as :

– Power generation

– Petroleum refining & petrochemicals

– Cement industry

– Chemicals & pharmaceuticals production

– Fertilizer production

– Mining manufacturing

– Humidification in textile mills

– building Ventilation, etc..

For additional information please refer to Northern Industrial Co. web site http://northernindustrialsupplycompany.com/index.html

Oleg Cthetchel
Process Ventilation Engineer
Northern Industrial Co.
http://northernindustrialsupplycompany.com/products/industrialfan_blowers.html
http://northernindustrialsupplycompany.com/products/ventilators.html

Selection of Appropriate Axial Fan for Building Ventilation

fan vaneaxial tubeaxial blower ventilator duct inline high pressure industrial commercial exhaust booster boosting air

fan@cogeco.ca

fan,vaneaxial,tubeaxial,blower,ventilator,duct,inline,high,pressure,industrial,commercial,exhaust,booster,boosting,air

***

Axial Fans & Blowers – High Temperature

Canada Fans Co. now offers high temperature construction on its axial fans. There are a few steps of fan heat construction available: 200 F, 725 F, 800 F. High temperature inline fans are ideal for industrial oven and dryer exhaust systems where pressure requirements are minimal and compact light-weight designs are advantageous.

High Temperature Fans

200 F High Temperature Duct Fans come with special heat bearings and a belt drive with increased safety factor.

Tubeaxial Fans

650 F Tubeaxial Fan design involves special belt tunnel cooling system that induces a flow of cooler, ambient air through the belt well and inner tube, cooling the fan’s internal components. Depending on temperature requirements, modifications include high-temperature alloy fan wheel, special drive components, and modifications to provide internal ambient air cooling.

Fans with ambient air cooling systems handling hot airstreams must have sufficient airflow and be kept in operation until airstream temperatures cool below 120 F to prevent damage to the fan unit. The Tubeaxial fan ambient air cooling system is only effective while fan is operating.

Vaneaxial Fans

800 F Vaneaxial Fans are designed to operate continuously at temperatures to 800 deg. F, and include an auxiliary cooling fan that forces air through the bearing compartment and exits out through the insulated belt opening taking away excessive heat from the shaft and bearings. A high temperature shaft seal is also standard on this design.

Fans handling hot airstreams must have sufficient airflow and be kept in operation until airstream temperatures cool below 120 F to prevent damage to the fan unit. The Tubeaxial fan ambient air cooling system is only effective while fan is operating.

High Temperature Fans Specifications

The Canada Fans complete high temperature fans line now include:

– Operating up to 2200 F, centrifugal, axial and plug fan types;
– Pre-engineered and custom made fans for all types of applications with vaiety of impeller types and accessories;
– Canada Fans engineers provide a professional advice and recommend a right fan for every application & oven / plenum design;
– The fan offering provides competitive replacement fans to Garden City, Lau, IGE, Alloy Fabricating fan models; repairs, re-build & balancing;
– Unique high temperature water-cooled motors for operation up to 2300 F;

in the two major types of high temperature fans – centrifugal and axial:

Centrifugal Wheels:

* Multiblade forward curve wheel. This type of wheel is usually specified where there is a necessity for large volumes of flow against low to medium static pressure requirements. The forward curve blade is that it delivers the same volume of air as either the backward or radial blade wheel, at a lower fan speed, which is important due to wheel stresses at elevated temperatures. This fan is the most common type used in all types of heat treatment operations except where a buildup of material on the blades could occur, as wheel unbalance would result.
* Radial Blade, paddle wheel type fans. This type of wheel is usually specified where there is a necessity for medium volumes of flow against medium to large static pressures. The paddle wheel is considered a self cleaning type of wheel. It could be used where there are various materials or dust in the air stream. Due to its structurally strong design, it is used in many heat treatment applications at very high temperatures where maximum fan longevity is desired.

Axial Blade Wheels:

* The axial blade wheel is usually specified where there is a need for very large volumes of flows against low static pressure. Axial wheel like the multi-blade forward curve type wheel could cause an axial fan to deliver different air volumes at the same static pressure, if the total pressure requirement of the fan system was underestimated. This type of fan is ideally suited where a large volume of flow is required with a minimum of duct work and is used extensively for small and large furnaces, such as aluminum annealing.

For additional information please refer to http://northernindustrialsupplycompany.com/products/industrialfan_blowers.html.

Oleg Cthetchel
Canadian process air systems developer
Canada Fans Co.
http://northernindustrialsupplycompany.com/products/index.html
http://northernindustrialsupplycompany.com/manufacturers.html

High Temperature Axial Ventilators

fan blower ventilator duct tubeaxial vaneaxial high temperature pressure thermo IGE alloy engineering industrial gas garden city circulating circulation oven exhaust plug air kit centrifugal axial

fan@cogeco.ca

fan,blower,ventilator,duct,tubeaxial,vaneaxial,high,temperature,pressure,thermo,IGE,alloy,engineering,industrial,gas,garden,city,circulating,circulation,oven,exhaust,plug,air,kit,centrifugal,axial

http://www.nisco.net/tchetchel.gif

***

Industrial Fans Manufacturer & Supplier

Canada Fan sales offices are located throughout North America and manufactured around the world. Wherever you are, “We want you to enjoy doing business with us.” Leave it to Buffalo Fan to take a perfectly reliable fan and offer a quieter, more efficient, less costly alternative. Canada Fan Corporation is committed to offering a wide variety of fans to meet your needs. Please visit our link, below, to view our capabilites and vast selection of designs.

Typical Industrial Fan Applications

Typical applications include air cleaning systems, mechanical draft, chemical processes, kiln exhaust, mine ventilation, gas recirculation, sinteric and cryogenic service.

Canada Fan / Canada heavy duty axial and centrifugal fans are designed to handle applications involving erosive and corrosive gases, large capacities, high pressures and temperature extremes.

To meet these operating conditions, Canada Fan / Canada heavy duty fans are designed and selected with the use of modern computer techniques guided by over 100 years of fan engineering experience. Comprehensive testing confirms design decisions. Quality manufacturing standards guarantee long service life.

Industrial Fans & Blowers Excellence

Over the years, Canada Fan / Canada supplied fans, blowers and pumps to a wide range of industries and applications. When prolonged service wears fan wheel the logical replacement is a new fan wheel built to the original design. A technical support and sales agent will get a replacement wheel, shaft, bearings, accessories, etc. in the shortest time. She, or he may also recommend changes to extend service life and performance of your machinery, including special materials of construction, explosion-proof and spark-resistant design, variety of coatings and accessories, intended to meet practically any application needs.

Best Industrial Fans & Blowers Performance

Canada Fan air moving products are best know for “industrial quality” assuring reliable performance, relentless dependability and longevity. A staff of specially trained engineers will design a dependable fan that exactly fits customers’ dimensional and performance requirements.

Solving difficult and unique air moving problems has earned Buffalo Fan a reputation for exceptional performance and reliability. Whether it’s energy related or industrial processing or simply moving a precise volume of air, a staff of specially trained engineers will design a dependable fan that exactly fits your performance and dimensional requirements.

Canada Fans are sold and serviced by air movement professionals. We can help you explore your needs and will be pleased to work with you.

Additional information can be found at the Northern Industrial web site http://northernindustrialsupplycompany.com/products/ventilators.html

Oleg Cthetchel
Air Process Systems Engineer
canablower@cogeco.net
Canada Fan Co.
http://northernindustrialsupplycompany.com
http://northernindustrialsupplycompany.com/burlington/request6.html

Canada Fan / Canada

airknife@cogeco.ca

Oleg Tchetchel

ventilator,fan,blower,centrifugal,axial,radial,pressure blower,high temperature,high pressure,PRV,propeller,industrial,building,ventilation,ventilating,high volume,air,circulation,circulating,wall,roof,exhaust,supply,wheel,blade,impeller

chicagoblower

chicagoblowerc

fan@cogeco

***

Canada Fans Blower Fan Supplier

Canada Fans heavy duty fans are designed and selected with the use of modern computer techniques guided by over 100 years of fan engineering experience. Comprehensive testing confirms design decisions. Quality manufacturing standards guarantee long service life.

Industrial Axial and Centrifugal Fans

Canada Fans heavy duty axial and centrifugal fans are designed to handle applications involving erosive and corrosive gases, large capacities, high pressures and temperature extremes.

Typical applications include air cleaning systems, mechanical draft, chemical processes, kiln exhaust, mine ventilation, gas recirculation, sinteric and cryogenic service.

Industrial Fans and Blowers – A long history of excellence

Over the years, Canada Fans supplied fans, blowers and pumps to a wide range of industries and applications. When prolonged service wears fan wheel the logical replacement is a new fan wheel built to the original design. A technical support and sales agent will get a replacement wheel, shaft, bearings, accessories, etc. in the shortest time. He, or she may also recommend changes to extend service life and performance of your machinery, including special materials of construction, explosion-proof and spark-resistant design, variety of coatings and accessories, intended to meet practically any application needs.

Canada Fans air moving products are best know for “industrial quality” assuring reliable performance, relentless dependability and longevity. A staff of specially trained engineers will design a dependable fan that exactly fits customers’ dimensional and performance requirements.

Solving difficult and unique air moving problems has earned Canada Fans a reputation for exceptional performance and reliability. Whether it’s energy related or industrial processing or simply moving a precise volume of air, a staff of specially trained engineers will design a dependable fan that exactly fits your performance and dimensional requirements

Canada Fans are sold and serviced by air movement professionals. We can help you explore your needs and will be pleased to work with you.

Canada Fans Corporation is committed to offering a wide variety of fans to meet your needs. Please visit our link, below, to view our capabilites and vast selection of designs. Buffalo Fan sales offices are located throughout North America and manufactured around the world. Wherever you are, “We want you to enjoy doing business with us.” Leave it to Canada Fans to take a perfectly reliable fan and offer a quieter, more efficient, less costly alternative.

Additional information can be found at the Canada Fans company web site http://www.canadianblower.com/ahu/index.html

Oleg Tchetchel
Air Systems Designer
oleg.tchetchel@canadablower.com
Canada Fans
http://canadianblower.com/hvac/index.html
http://canadianblower.com/index.html

Canada Fans Fan Blowers

oleg.tchetchel@canadablower.com

explosion proof fan,explosion proof blower,explosion proof ventilator,spark resistant fan,spark resistant blower,spark resistant ventilator

***