Centrifugal Blower Manufacturer – Page 2 – Canada Fans Industrial Blowers & Fans

Commercial Extractor Fans

Today there are a wide range of commercial extractor fans available on the market to cover just about every application imaginable; from large commercial applications, such as restaurant kitchen extractor systems, to quiet airflow systems that are virtually silent in operation.

While a commercial kitchen extraction system, commonly made in stainless steel can cost several thousand pounds to buy and install, a large vent-axia through wall extractor fan may be fine for a small hot food business such as a shop making toasted bacon sandwiches.

The new quiet airflow extraction systems are proving popular as they have a high airflow, yet can barely be heard running. This helps keep environmental noise down, and this is often important in an office workplace.

Commercial Inline Fans

Commercial in-line fans are available that sit above the ceiling, often some distance from the room they are actually extracting the air from. They are connected to vents in the ceiling by ducting, which then connects to the inline fan, and then expels the air through more ducting to a grill in an outside wall.

This type of fan has to be used in certain “classes” of environment by law, whereby no electrically powered unit can be placed within a certain distance of damp areas, such as shower rooms as an example.

When buying a commercial extractor fan, you will have to take more into consideration than when purchasing a domestic extractor fan. The reason for this is that whilst a domestic fan may be cheap to buy and install, and can be replaced at a low cost if it breaks, the same cannot be said of a commercial extraction system.

Large Commercial Extractor Fan Installations

Most large commercial extractor fan installations will cost several thousand to buy, and will need professional installation. So given the investment you may make in one, you need to be buying with a reputable supplier, as you may be installing it in an environment where you may have to stop work if the extractor fan system breaks down, such as in a commercial kitchen.

If this happens, you need to know that someone can come out and fix your extractor fan very fast, as if you have to close your kitchen down, you will be losing money until it is fixed. So you need to do some research about the company you are buying your fan from, and ensure that they can provide a fast call out, and that they carry sufficient spare parts.

Additional information can be found at the Industrial High Pressure Blower Company web site http://www.highpressureblower.net/OEMFans.html

Alex Todorovo
Industrial Mechanical Process Engineer
High Pressure Blower Co.
alex.todorov@canadablower.com
http://www.highpressureblower.net/canadianbloweraxial.html
http://www.highpressureblower.net/MakeUpAirFans.html

Commercial Fan

fan blower ventilator high temperature pressure industrial super transfer air gas positive negative heavy duty capacity process

alex.todorov@canadablower.com

fan,blower,ventilator,high,temperature,pressure,industrial,super,transfer,air,gas,positive,negative,heavy,duty,capacity,process

***

Tags:
Axial Roof Ventilators, Axial Ventilator, Blower, Blower Fan, Blower Fan Canada, Blower Fan Suppliers, Blower Industrial, Centrifugal Blower Fan, Centrifugal Blower Fan Suppliers, Industrial Centrifugal Blower, Industrial Centrifugal Fan, Industrial Fans, Industrial Fans and Blowers, Industrial Pressure Blower, Inline Belt Drive Fans, Inline Exhaust Fans, Material Handling Fans, Mixed Flow Inline Fan, Radial Blade Belt Centrifugal Fan, Radial Blade Centrifugal Fan, Radial Blade Fan, Radial Blade Pressure Blower, Roof Exhaust Fans, Vaneaxial Fans Aluminum Wheel, Vaneaxial Power Roof Ventilator, Wall Exhaust Fans, Wall Supply Fans

Exhaust Fans

The practical designs of modern homes are more focused on energy conservation. Making a home practically air-tight reduces heating requirements thus saving on electricity costs. This may be a great way to save money and help the environment, but it also leads to poor air circulation inside the house. Poor air quality can lead to a variety of cardiovascular diseases, ruined paint and damaged furniture which is why it is important to have good air circulation inside the home. The best way to do this is to install ventilation exhaust fans.

Types of Exhaust Fans

There are many different types of exhaust systems and getting an idea of how each one works will give you an idea of what type will be the best for your home. Different sized homes will have different ventilation requirements. Larger homes will require a variety of ventilation fans to keep the air from getting stale.

Wall Mounted Exhaust Fan Systems

The most common types of ventilation air purifying fans are wall mounted, ceiling mounted, inline fans, combination, exterior remote mounted and kitchen range exhaust fans. It is best to have ducting installed in areas where a visible fan would not blend in well. Areas like the living room, dining room, den and bedrooms would be good places to have ducting installed. Stale air runs through the ducting and exits the house via an exterior fan that expels the air outside, or busing using inline fans that are contained inside the actual ducting.

Ceiling or Wall Mounted Exhaust Fans

Kitchens, attics, laundry areas, bathrooms, garage and storage areas can be installed with either ceiling mounted or wall mounted exhaust fans if the area is situated beside an exterior wall.

It is important that all the areas inside a home need to have air circulation so that pollutants, pathogens or even humidity does not accumulate and lead to costly repairs or health problems. Be sure to select ventilation exhaust fans that are suitable for each area of the home.

For more information about proper building ventilation please visit the ABB Blower company web site http://www.fanblower.com/motor_cooling_fan.htm

Susann Terlitski
Designer of Industrial Air Handling Units
Fan and Blower Co.
abbblower@abbblower.com
http://www.fanblower.com/axial_flow_fan.htm
http://www.fanblower.com/inline_fan.htm

Exhaust Fans

air handling unit industrial airhandler AHU conditioner commercial ventilator fan blower building ventilation ventilating cooling heating circulation circulating roof top supply

abbblower@abbblower.com

fan,blower,ventilator,high,temperature,pressure,industrial,super,transfer,air,gas,positive,negative,heavy,duty,capacity,process

***

Industrial Building Ventilation

Based on the objectives and funds available, one can now consider different alternatives for industrial building ventilation and select the best method to use in calculating air volume requirements. A description of these methods follows. This is a time-honored approach to a determination of air volume requirements. It is based on the theory that a complete change of air in a room or building should be made at a certain time frequency. The rate selected is frequently an arbitrary decision. It may be based on experience with similar installations or may be established by a health or safety code. Many fan manufacturers have published charts that show recommended rates of air change for typical installations. Although the rate of air change method of calculating air volume has been used for many years, Buffalo Fan engineers have found it unsatisfactory except in relatively small buildings or rooms. For jobs that involve personnel comfort. this method is not recommended if the building is over 50,000 cubic feet in content or more than l00′ in length.

Considerations for Building Ventilation

The volume of air required to operate a ventilating and cooling system is a very fundamental requirement. Before air volume is estimated or calculated, careful consideration should be given to the following factors. Be sure that the decision you make will accomplish the most important objectives or will overcome the most important problems. This should be the overriding consideration in the selection of a system of ventilation. Availability of money to finance the system is a factor that must be considered early in the planning stage. The funds available will affect the objectives you set and will influence the system of ventilation selected to meet the objectives.

CFM per square foot of floor area method

CFM per square foot of floor area method: this method of calculation is a modern adaptation of the rate of air change formula. Total air volume (cubic feet per minute) is determined by multiplying the total square feet of floor area by an arbitrary CFM per square foot figure. The figure selected may be as low as 2 CFM or as high as 12 CFM per square foot. Four CFM per square foot has been recommended as a minimum for summer ventilation of large assembly type operations. This method of calculation, like the rate of air change method, is likely to produce unsatisfactory results in many cases. Failure to control air distribution and air velocity can be a major weakness in the whole concept. Selection of a CFM per square foot figure should be based on experience and a proven method of air distribution.

Rate of air velocity method

Rate of air velocity method: This method of calculating air volume needed for a system is highly recommended by American Coolair. A breeze conditioning system can be highly effective in providing personnel comfort in hot weather if the recommendations outlined below are observed. It has been determined from field experience that an average air velocity of 150 feet per minute (FPM) to 200 FPM is usually sufficient for personnel cooling under summertime conditions. The CFM required to do the job is calculated by multiplying the cross section of an area through which the air is to move by the desired velocity. This is expressed in the following formula.

Factors Affecting Average Air Velocity

As building size increases, there are factors that will affect the average air velocity through the cross section of the building. The longer the building, the greater the amount of air leakage from windows, doors, elevator shafts, etc. To offset this air leakage, air velocity should be increased. This is done by relating the calculated velocity to the length of the building. The results will provide an effective velocity of approximately 150 ft./min.

Industrial Ventilators

In some buildings. it is not possible or practical to install a complete ventilation system. In such situations, zone cooling may be effectively used. The problem is similar to a spot cooling application, but usually involves a relatively larger area. Effective zone cooling may be accomplished by use of air circulators. See Air circulation below. A very satisfactory zone cooling method is the use of supply-type PRVs to flood the problem area with fresh, cooler air. The adjacent drawing and zone cooling table illustrate the capacity of several American Coolair PRV models to effectively cool an area. The figures are based on discharge of air approximately l5 feet above floor level.

Additional information can be found at the Canada Blower company web site http://canadablower.com/ahu/index.html

Susan Terlitski
Air Handling Units Engineer
Canada Blower
canadablower@canadablower.com
http://canadablower.com/hvac/index.html
http://canadablower.com/oem/index.html

Adequate Buildings Ventilation

canadablower@canadablower.com

ventilation fan,ventilating fan,building ventilation,building ventilating,ventilator,fan,blower,roof fan,wall fan,roof ventilator, wall ventilator

buffaloblowercom

***

Industrial Exhaust Fans

Exhaust Fan Systems

Ventilator Fans

Wall & Roof Exhaust Fans

Kitchens, attics, laundry areas, bathrooms, garage and storage areas can be installed with either ceiling mounted or wall mounted exhaust fans if the area is situated beside an exterior wall.

Ventilator Exhaust Fans for the Home

For more information about proper building ventilation please visit the ABB Blower company web site http://www.fanblower.com/motor_cooling_fan.htm

Susann Terlitski
Designer of Industrial Air Handling Units
Fan and Blower Co.
abbblower@abbblower.com
http://www.fanblower.com/axial_flow_fan.htm
http://www.fanblower.com/inline_fan.htm

Exhaust Fans

air handling unit industrial airhandler AHU conditioner commercial ventilator fan blower building ventilation ventilating cooling heating circulation circulating roof top supply

abbblower@abbblower.com

fan,blower,ventilator,high,temperature,pressure,industrial,super,transfer,air,gas,positive,negative,heavy,duty,capacity,process

***

Industrial Fans & Blowers – Commercial & Industrial Uses

Canada Fans provides fans for every type of commercial structure including airports, arenas, stadiums, distribution centers, malls, offices, and retail. Canada Fans also offer smoke and heat exhaust fans that are UL listed for Smoke Control Systems and a full line of kitchen fans that are UL 762 listed for the exhaust of grease-laden air. Canada Fans engineers design, test, and manufacture fans for all types of buildings, including condos, custom homes, offices, malls, airports, arenas, and stadiums. We are able to meet your most precise requirements for a variety of HVAC equipment, including all types of custom, package air handlers and roof top units. In addition, Canada Fans can provide exhaust for restrooms, elevator shafts, parking garages, and jet bridges; stairwell pressurization; rooftop and sidewall supply and exhaust, including smoke and heat exhaust fans that are UL listed for Smoke Control Systems, as well as kitchen fans that are UL 762 listed for the exhaust of grease-laden air.

Exhaust Fans

Canada Fans supplies thousands of fans to universities, hospitals, laboratories and research facilities, military bases, hotels, convention centers, and cruise ships around the world; working closely with architects, engineers and contractors to design and test fans that can meet the most precise quality and reliability requirements. Canada Fans makes smoke and heat exhaust fans that are UL listed for Smoke Control Systems, kitchen fans that are UL 762 listed for the exhaust of grease-laden air, and a full line of laboratory and fume exhaust systems. Canada Fans provides fans for numerous residential building applications, such as stairwell and elevator shaft pressurization; kitchen, restroom, and pool exhaust; and every aspect of HVAC, including air handlers, gravity ventilators, and large rooftop units.

Blowers & Fans For Exhaust Ventilation

Manufacturing facilities require a large amount of ventilation to maintain a healthy work environment for the people working within the buildings. Canada Fans designs and builds fans to control and handle the exhaust, supply, and make-up air requirements for all types of manufacturing environments and spaces. The exhaust of welding and other noxious fumes and dusts, as well as the exhaust of hot air produced from ovens and other high temperature processes, are essential to providing safe and comfortable working conditions. In many cases, the building heating, cooling, and air conditioning (HVAC) requirements are also critical for proper production control and working conditions. A wide variety of businesses, industries, medical facilities, and institutions require ultra clean environments for research and development as well as production of specialty products and equipment. These facilities demand high filtration and positive pressures inside the clean room space to control the process and limit potential contamination. Other requirements typically include variable air volume, high efficient air moving equipment, low noise, and ultra-low vibration levels from the mechanical equipment.

Energy Efficient Fans & Blowers

Among many other changes, the green revolution has created a greater need for more energy efficient fans and ventilation equipment. As a leader in the fan industry, Canada Fans engineers and manufactures high efficient products for a wide variety of green friendly applications including LEED building designs, biofuel and biomass production plants, landfills, solar film manufacturing facilities, as well as numerous waste energy and heat recovery systems. Regardless of how unique or specialized your process is, Buffalo Blower can customize our products to meet virtually any requirement.

Large Industrial Fans & Axial Ventilators

Canada Fans is well known for leveraging its design and manufacturing capabilities when constructing the heavy duty fans required for marine applications. Such marine duty fans are used for many purposes including boiler combustion air, mechanical ventilation, off shore rig diesel generator exhaust disbursement, pressurization, engine cooling, and dust control. Our air moving equipment can be found on drilling rigs, production platforms, tug boats, cruise ships, ferries, and cargo ships. We offer a number of features to meet the specific needs of the marine industry. These include shortened axial fan housings for operating in tight spaces, cast aluminum impellers and hot dip galvanized steel components for extended durability, spark resistant construction for potentially explosive air streams, water tight electrical connections to withstand corrosive environments, and IEEE 45 marine duty motors for both above deck and below deck installations.

Blower Fan Standards

In addition to our extensive fan design and manufacturing experience, Canada Fans offer a number of products meeting requirements of the marine industry’s governing and standard organizations including:

• Air Movement and Control Association (AMCA) – Spark Resistant Construction
• American Bureau of Shipping (ABS) – Type Approval for Ventilation and Non-Sparking services

Additional information can be found at the Canada Fans company web site http://www.canadafans.com

Susan Terlitski
Canadian Process Air Systems Designer
canadablower@canadablower.com
Canada Fans
http://canadafans.com
http://canadafans.com

Commercial Ventilator and Fan

canadablower@canadablower.com

ventilator,commercial,industrial,fan,blower,power roof fan,power roof ventilator,roof exhaust fan,roof supply fan

buffaloblowercom

buffaloblo

***